Hydraulic Push-Pullers

17 1/2, 30-50 Ton

Place Enquiry

Catalogue PDF

The power to make impossible jobs become routine.

• Can apply a hydraulic pushing or pulling force, depending on how the puller is set up.
• Each unit includes perfectly matched hydraulic components that can be detached from the Push-Puller for other tasks requiring dependable Power Team power; assuring maximum return on your investment.
• Optional leg kits adapt your Push-Puller to extra long or extra short reach.
• A wide variety of threaded adapters, bearing pulling attachments and internal pulling attachments can be used in combination with our Push-Pullers .

Selection and capacity rating

Each Push-Puller's specified tonnage "capacity" is determined using its standard legs in tension. Using longer legs, or a setup in which the legs are in compression, will reduce the capacity. Always select the largest capacity puller and the shortest legs that will fit the job.

Power Twin cylinder

This unique center-hole cylinder powers each Push-Puller . Puller screw runs right between the twin spring cylinder. A basic head allows you to change from a tapped hole to a plain hole by merely changing the head insert.

17 1/2 ton capacity Push-Puller

No. PPH17 - Push-Puller with RT172 center-hole Power Twin cylinder, cylinder half coupler, P55 pump, 9767 6-ft. hose, 9798 hose half coupler, 16 1/2" legs, 24827 leg ends, 1"-8 x 20" lg. adjusting screw and adjusting crank. Wt., 59 lbs.
No. PPH17R - Same as above, but without P55pump, 9767 6-ft. hose and 9798 hose half coupler. Wt.,40 lbs.
No. 1062 - Puller only. (Cylinder, pump, hose, coupler, screw and crank not included.) Wt., 20 lbs.

USE WITH: Bearing pulling attachments: Nos. 1124 and 1130. Pulley pulling attachment: No. 679. Internal pulling attachment: No. 1154. Legs: Nos. 1104, 1105, 1106, 1107 and 1108 - Pair of legs for 17 1/2-ton capacity Push-Puller.

30 ton capacity Push-Puller

No. PPH30 - Push-Puller with RT302 center-hole Power Twin cylinder, cylinder half coupler, P55 pump, 9767 6-ft. hose, 9798 hose half coupler, 18" legs, 28390 leg ends, 1 1/4"-7 x 24" lg. adjusting screw and adjusting crank. Wt., 102 lbs.
No. PPH30R - Same as above, but without P55 pump, 9767 6-ft. hose and 9798 hose half coupler. Wt., 82 lbs.
No. 1070 - Puller only. (Cylinder, pump, hose, coupler, screw and crank not included.) Wt., 42 lbs.

USE WITH: Bearing pulling attachments. No. 680 (Use two 8012 adapters to connect to puller.) Pulley pulling attachment: No. 679. Internal pulling attachment: No. 1166. Legs: Nos. 1109, 1110 and 1111 - Pair of legs for 30 ton capacity Push-Puller.

50 ton capacity Push-Puller

No. PPH50 - Push-Puller with RT503 center-hole Power Twin cylinder, cylinder half coupler, P55 pump, 9767 6-ft. hose, 9798 hose half coupler, 24" legs, 1 5/8"-5 1/2 x 30 3/8" lg. adjusting screw and adjusting crank. Wt., 201 lbs.
No. PPH50R - Same as above, but without P55 pump, 9767 6-ft. hose and 9798 hose half coupler. Wt., 181 lbs. No. 1076 - Puller only. (Cylinder, pump, hose, coupler, screw and crank not included.) Wt., 106 lbs.

USE WITH: Bearing pulling attachments: Nos. 1128 and 1129. Legs: Nos. 1112 and 1113 - Pair of legs for 50 ton capacity Push-Puller.