Slide Hammer Pullers
Place Enquiry |
Catalogue PDF
Blind hole puller set - Removal of bearings, bushings, sleeves and other friction-fitted parts from blind holes can now be accomplished with ease. Set provides selection of expanding collets 5/16" to 1 3/4" I.D. Collet is placed through bore of part to be removed, then expanded with actuator pin so that lips of collet secure a positive grip for pulling. Pulling force is exerted by means of a forcing screw and bridge assembly or with a slide hammer.
No. 981
Blind-hole puller set with slide hammer, forcing screw, bridge, actuator pins, collets, and storage box. Wt., 21 lbs.
Slide hammer puller set
This very handy set is ideal for those close-quarter, inside pulling jobs. Very practical for pulling motor, generator, and magneto bearings. Also good for removing small-bore bushings, bearings, and oil seals.
No. SS2 - Slide hammer puller set. Wt., 5.8 lbs.
Slide hammer puller set
This useful set contains a reversible-jaw slide hammer puller with a 2.5 lb. sliding hammer plus an assortment of special jaws (3 of each size) and adapters. In this set, you get all the versatility you demand of a slide hammer puller.
No. 1178 - Slide hammer puller set with 2.5-lb. sliding hammer. Wt., 13.8 lbs.
Bearing cup remover
The 7136 is perfect for pulling internal bearing cups, seals, bushings, etc. Jaw spread - 15/16" to 3 1/4", reach to 3 1/2". Use with any slide hammer having 5/8"-18 thread (Power Team 1155, 1156 or 927 Push-Puller ).
No. 7136 - Universal bearing cup remover. Wt., 1.5 lbs.
Pilot bearing pullers -
These very versatile pullers are built especially for inside pulling jobs, and particularly for removing flywheel pilot bearings on machines and construction vehicles. Also very practical for pulling motor, generator and magneto bearings.
Special slide hammer puller
Ideal for pulling jobs in very close quarters, as in removal of small-bore bushings, bearings, oil seals, etc. Internal pulling attachment has jaw spread of 1/2" to 1 3/8". Handle end has a 1/2"- 20 thread.
No. 1173 - Slide hammer puller. Wt., 3.5 lbs.
No. 1174 - Puller head, less slide hammer.
Basic slide hammer units
Compatible with internal pulling attachment (see page 198). Compatible with threaded adapters (see page 204-205). 24" in length, 5/8"-18 threaded end.
No. 1155 - Basic slide hammer unit with 5 lb. hammer. Wt., 7.3 lbs.
No. 1156 - Basic slide hammer unit with 2.5 lb. hammer. Wt., 4.8 lbs.
Reversible-jaw slide hammer pullers
Ideal for pulling gears, bearings, outer races, grease retainers, oil seals, etc. Two or three jaws may be used and positioned for "inside" or "outside" pulling jobs. Both have 5/8"- 18 threaded end so attachments and adapters may be used.
No. 1176 - Slide hammer puller with 2.5 lb. hammer, 27241 two-way head and 34698 jaws.
No. 1177 - Same as 1176 but with 5 lb. hammer.
Slide hammer pullers with cup pulling attachments
These combine a basic slide hammer with No. 1152 internal pulling attachment for removing oil seals, outer races, and bearing cups from blind holes.
No. 1157 - Slide hammer puller consisting of 1156 slide hammer and 1152 internal pulling attachment.
No. 1158 - Same as 1157 but with 1155 slide hammer.