International Endheads for Pick-a-Pack Hydraulic Power Packs

The full range of KN Series SPX Flow Stone hydraulic power unit endheads. The international endhead is a unique part of the power pack set up and is the key passage for fluid to pass around the Hydraulic system. The endhead is also the main connection point for some of the modular Power Pack’s core components connecting the reservoir, motor, valves and load lowering solenoid. The endhead is available with either UNC or Metric Footmounts and can be supplied with NPT or BSPP ports.
Results per page: 24 36 96
Set Ascending Direction
Power Team KN10 Pick-a-Pack Endhead with Metric Footmounts and BSPP Ports
    • Central to pick-a-pack hydraulic units
    • Fitted with metric footmounts
    • Fitted with BSPP ports
    The central component for a SPX Flow / Stone hydraulic pick-a-pack power unit, the KN10 Endhead comes with metric footmounts and BSPP ports. Learn More
    £68.82 £57.35 £137.64 Save £68.82
    Power Team KN09 Pick-a-Pack Endhead with Metric Footmounts and SAE Ports
    • Central to pick-a-pack hydraulic units
    • Fitted with metric footmounts
    • Fitted with SAE ports
    The central component for a SPX Flow / Stone hydraulic pick-a-pack power unit, the KN09 Endhead comes with Metric footmounts and SAE ports. Learn More
    01332 576850

    Out of Stock

    Results per page: 24 36 96
    Set Ascending Direction

    Pick-A-Pack Product Range

    All of the mating components of the Pick-A-Pack range are fully interchangeable. They’re modular in design, with the “international” endhead featuring as the key component. From here, you can use any combination of pump, reservoir, and drive motor, and control valving can be assembled into or manifolded onto this endhead. Three different configurations are available. These include the following porting options: NPTF, SAE and G3/8.

    Select Pump and DC Motor Combination

    Selecting the correct motor and pump for your application is essential. After all, if you choose the incorrect motor, you won’t have the correct levels of pressure, flow and electrical amp draws in the design circuit. In addition to this, if you select the wrong pump and DC motor combination, the motor could overheat, becoming inoperable in the process. If you’re unsure which motor is right for your application, our experts can help. There are motor curves for both S2 and S3 duty cycle categories.

    There are motor curves for both S2 and S3 duty cycle categories.

    • S2 – Absolute Continuous On-time. Indicates how long a motor can be run continuously before it must be allowed to cool back to ambient temperature.
    • S3 – Percentage On-time. This is calculated on a 5 minute duty cycle and shows the time the motor can be run continuously before it overheats.
    How to choose a power pack

    Repair & Service Centre

    Here at SGS Engineering, we offer a free same-day strip down and inspection service. In addition, we also have a fully equipped workshop, as well as a number of experienced and skilled engineers who have years of knowledge to draw upon when it comes to repairing and servicing hydraulic power units. This means that, when you buy SPX hydraulic power packs with us, you can reduce your expensive down time.

    An Example of How to Select a Motor and Pump

    For our example, we will assume that the chosen application requires:

    • 12V DC supplied power
    • Intermittent operation
    • A flow rate of 1.5 GPM at 2000 psi.

    From this, if continuous operation is a requirement, we know that a Hi-power 12V motor must be selected. A standard 12V DC pump motor graph then shows us that a KP-2.5 pump (2.5cc/rev) is required, drawing 260 amps with this combination.

    As the application is intermittent, an S3 graph can be used to show us how long the motor can operate as a percentage of 5 minute intervals without the need to cool to ambient temperature. In this instance, a standard duty motor (KMD1 or KMD2) has an 8% on-time. This equates to 24 seconds on and 276 seconds off continuously. If the example was expanded to KMD3, we would see a 13% on-time, or for 39 seconds on, 261 seconds off continuously.

    A relief valve is an extremely important piece of equipment. This is because it has the ability to limit the amount of pressure created by a power unit. As Stone AFC pumps have the capability to generate in excess of 5000 psi, they’re an incredibly handy piece of equipment because if pressure remains unlimited, due to the absence of a relief valve, mechanical components can become damaged, leading to injury or death.

    As a result, you must ensure that every mechanical component selected in the design of the application can handle the levels of working pressure required. Once you have calculated working pressure, you must select a relief valve that allows for full flow at this working pressure. Often, a relief valve will “crack” at around 80% of their pressure rating, opening to full “dump” to tank once the rated pressure is obtained. This is sometimes referred to as full bypass pressure and flow. As a rule, the working pressure should be less than 80% of the rated relief valve pressure.